• Frys.com #7591556
  • Manufacturer: POLK AUDIO
  • UPC #747192121945
  • Model #PA D5000.5
  • The PA D5000.5 is our big gun 5-channel beast that enables you to drive all your speakers and a subwoofer and never break a sweat. A toroidal transformer helps keep the PA D5000.5 neatly packaged in a sleek aluminum extruded design under 2-inch tall while it pumps out gobs of clean, efficient power. A low THD, a high signal-to-noise ratio, plus wide bandwidth frequencies, make the PA D5000.5 uncompromising performance in your any vehicle's sound system.

    The PA D5000.5 is capable of bridging two full-range channels into a single full-range channel with higher output power. For instance, the front channels (FL and FR) when wired correctly will increase the output power from 70W per channel to 200W per channel (for a 4 ohm load). The same can be done for the rear channels (RL and RR). The most common configurations are four full-range channels and a subwoofer channel, or two bridged full-range channels and a subwoofer channel.

     

     

    Share this:

    Share on Google+


    Detailed Description
    (Manufacturer # PA D5000.5 )

    Features
    Super-efficient class D design — Runs much cooler than conventional amps.

    High-speed MOSFET switching — Power supply with outputs stable into 2 ohm loads for full range channel speakers and 1 ohm loads for subwoofer channel.

    Protection — Thermal, DC offset, reverse DC voltage and short circuit protection.

    Sub 1/Sub 2 Inputs — Line level inputs for subwoofer signal from head unit

    SUB/INT source switch — In the INT position, the amplifier will filter the bass frequencies from the full range signal and send them to the subwoofer amplifier channel.

    SUB sonic filter — Attenuates the frequencies below the settings on the control.

    Remote bass level control — Set gain to match output from head unit.

    Rear Full, HPF switch — Selects between no filtering or a high pass filter to dial in your speakers' blending.

    Channel mode switch (4CH/ST) — In the ST position, the amplifier sends the same signal to the front and rear channels.

    Nickel-plated wire terminals & RCA connectors — Ensure maximum signal transfer.

    Stainless steel hardware — Used throughout won't corrode in humid environments.
    Specifications
    Electrical
    Total Frequency Response 20Hz-20kHz
    Signal-to-noise (Referenced to rated power) 105 dBA
    Remote Gain yes, for bass
    Distortion at Rated Power <0.1 %
    Minimum Impedance Bridged 4 ohms
    Minimum Impedance Not Bridged 2 ohms
    Protection Circuitry Thermal, DC offset, reverse DC voltage and short circuit; fuses: two 40 Amp ATC
    Subsonic Filter yes
    High Pass Filter
    Filter Slope 12dB/octave
    Filter Frequency 40Hz-400Hz(front)/40Hz-4kHz(rear)
    Low Pass Filter
    Filter Frequency 80Hz-4kHz(front)
    Max Sensitivity 200mV-6V dB
    Dimensions
    Cabinet Dimensions
    Height 1 13/16" (4.60cm)
    Width 13 5/16" (33.81cm)
    Depth 6 3/4" (17.14cm)
    Product Weight (each) 6.750 lbs. pounds
    With Panels
    Height 1 13/16" (4.60cm)
    Width 13 5/16" (33.81cm)
    Depth 6 3/4" (17.14cm)
    Amplifier Specs
    Power Specs 100W x 4, 400W x 1 RMS @ 2 ohms; 70W x 4, 200W x 1 RMS @ 4 ohms; 200W x 2 RMS bridged @ 4 ohms; 500W x 1 RMS @ 1 ohm (sub)
    Channels 5
    Channel Notes Bridgeable Class D MOSFET
    12V & Ground Cable Gauge 4AWG
    Amplifier Power Specs - RMS Power at 14.4V
    Watts per channel NOT bridged @ 1 kHz
    4 ohms 70 x 4 watts
    2 ohms 100 x 4 watts
    Watts per channel bridged
    4 ohms 200 x 2 watts








    In Stock, Same Day Shipping
    This product is in stock in our warehouse. You have a choice of Ground Service, 2nd Day Air, or Overnight Delivery for domestic orders.